Troubleshooting A Blurred Rifle Scope

Hunters who are starters to scopes or a hunter who is using giant magnification scopes may be familiar with the irritation of blurred targets and also bad image quality for more than one time.

It’s an easy thing to install if you know what you are doing. We discuss troubleshooting a blurred rifle scope in this article.

Moreover, things aren’t white and black when it gets down knowing the source of why the riflescope is blurry. Let’s check some common reasons responsible for this, and you can go back hunting quickly.

Troubleshooting If A Reticle That Is Blurry

This is almost certainly the primary cause of much resentment for owners of rifle scopes. The reticle would look blurred, and even it is not that obvious, a lot of users don’t realize how much they are gone on reticle sharpness.

To be clear, your scope requires to be appropriately focused for the eyes and your vision.

However, after a while, your eyesight may change, and you will need to refocus your scope. If you lend someone else your scope, they will need to adjust the focus for their own eyes; once you get it back, you would have to recalibrate to your vision.

Here is what you are required to do;

Step 1

In case you put on glasses when shooting, also have them on when your scope is being focused. If they have the caps, take them away from the scope.

If the eyepiece has a locking technique, you need to unlock it.

Always remember not to look directly at the sun because it causes permanent and severe damages to the eyes

Step 2

You have to turn the eyepiece routine; it is usually anti-clockwise

Step 3

Try and look for a white and black background like a sky. You shouldn’t focus your scope while you are looking at prey. You have to watch into and out of the scope for you to spot the blurred reticle.

Step 4

Permit your eye muscles to relax when looking on a faraway target. Turn the eyepiece notch in a clockwise direction, and you should swiftly look through the scope to identify the reticle and look away immediately.

This is important because you shouldn’t allow your eye muscles a way to recoup for the blurred reticle.

Step 5

You should continuously repeat the process of rolling the eyepiece and stare away until you get a sharp reticle.

Step 6

You may want to grab a keen of the diopter settings if your scope has one and also lock the eyepiece if needed. If several lots of individuals use this scope, you may have to use something like a pen to indicate your focus setting.

As soon as the reticle is sharp, crisp and black, you have rightly corrected the reticle as focused for your eyes. If you settle for an average reticle, quality would cause strain or fatigue to your eyes.

Troubleshooting a Blurred Rifle Scope at High Magnification

troubleshooting if reticle is blurry

A general poor image relates to the amplification use or the depth about what you are targeting.

Most of the times, poor image quality is usually related to shooting at a target in a very close range. Factory-set parallax which a lot of rifle scopes comes with has a parallax setting for 100-150 yards.

If you try to center on prey that is within 10-25 yards, it can be too near for the focusing capabilities of the rifle. Try and tune down the amplification and see if it becomes any better.

Parallax Focusing

If you have a rifle scope that has a position to the left or right of a turret or an AO (adjustable objective), then you have to make farther adjustments to improve your focus. This might be a reason why you are encountering blurry and bad image qualities.

The role of the adjustable objective is to pilot into attention the prey in connection with the reticle.

Adjusting to the parallax issues will be dependent on the type of parallax feature you have.

Adjusting with Side Focus

  • Evaluate your distance to your prey
  • Arrange it all past up the infinity setting
  • Turn it down until the image standard is clear and sharp
  • Your markings must be in line with the calculated distance
  • Adjust your magnification setting well for your intended shot

Adjusting with AO

  • Estimate your distance to your prey
  • Rotate the objective bell to correlate with the reference markings
  • Adjust the magnification to a power that is suitable for your shot
  • The image quality should be optimal and be corrected


Nearly all the time, a blurred rifle scope is due to a user error as you can see. It can be an out-of-focus scope or parallax playing some tricks on you too.

If you have been into all these troubleshooting processes, it’s going be a great time to take precedence of the warranty that came with it.

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.